FAAC Gate Parts & Welding Nationwide

FAAC Gate Parts & Welding in Miami Gardens: What to Know First

We provide independent FAAC gate parts replacement and welding repair throughout Miami Gardens, with most hinge, rail, and latch jobs completed same day or next morning. You’ll get a written price before any work starts, not a verbal ballpark you have to trust. Typical FAAC parts and welding work in Miami Gardens runs between $180 and $650 depending on what failed. Call (786) 789-0087 and Adrian will walk you through what’s likely wrong before we ever roll a truck.

Call (786) 789-0087

This page is for FAAC owners in Miami Gardens whose gate still runs but the metal’s giving out: hinges, posts, rails, weld points, rollers, latches. If your operator still moves the gate but something’s sagging, grinding, or sticking, you’re in the right place.

How FAAC Products Fail - and How We Fix Them

FAAC operators are genuinely well-built, but the metal around them lives in Miami Gardens humidity and salt air. Here’s what we actually see on service calls:

• Swing gate hinge sag on FAAC 400 and 412 operators: The operator is strong enough to keep pushing a gate that’s slowly dropping at the hinge. You get a gate that shudders at the start of travel and slams at the end. The operator gets blamed, but the hinge pin’s worn a quarter-inch and the leaf is riding low. We cut out the old hinge, weld in a new one, and set the operator’s travel limits to the new geometry.
• Post fatigue at the operator mount on FAAC 391 and 770 models: These operators torque against the post every cycle. After years of that, the post develops hairline cracks at the weld root, where the mount plate meets the post. A homeowner sees “the gate’s getting slower.” What’s actually happening is the post is flexing. We gusset the post or replace it entirely, then remount the operator and photograph the new weld.
• Rail wear on FAAC sliding gates: FAAC sliding operators are built to move a specific weight over a specific rail. When the rollers wear flat or the rail develops a groove, the gate starts chattering and the operator draws more current. We replace the rollers, and if the rail is grooved beyond tolerance, we weld a new rail section and grind it smooth.
• Latch and lock misalignment on FAAC estate gates: The gate may close fully but not latch because the gate’s center of gravity shifted as a hinge wore. The operator thinks the job is done; the homeowner hears a click that never engages. We re-weld the latch post or shim the receiver and reset the close limit so the lock actually throws.
• Weld fractures on decorative FAAC gate frames: Ornamental gates in Miami Gardens often have scrollwork welded to a box frame. Temperature swings and daily cycling cause those decorative welds to crack first. They’re not structural, but they look bad and rust spreads. We grind, reweld, and coat with a rust-inhibiting primer before paint.

Our FAAC Gate Parts & Welding Process

1. 1
   You call (786) 789-0087. A live person answers. You describe the symptom. We tell you honestly whether it sounds like a parts and welding issue or an operator problem.
2. 2
   We come out and look. Adrian or one of our technicians arrives with a written estimate already drafted based on your description. Before any work starts, we check the hinges, posts, rollers, and welds and give you a flat price in writing.
3. 3
   Parts decision: If the gate needs FAAC-specific parts, we’ve got OEM and quality aftermarket options. We’ll tell you the trade-off: OEM matches exactly but costs more; aftermarket is often the same steel but with a longer lead time saved by our local suppliers. You choose with the price in front of you.
4. 4
   The fix: Welding, hinge replacement, post replacement, rail repair, whatever’s needed. We document every step with photos.
5. 5
   Test cycle: We run the gate through its full travel at least twenty times, watch the operator’s behavior, and adjust travel limits so the motor isn’t fighting the new geometry.
6. 6
   You get a photo log and a written record. Yes, we do this on every single job. You’ll see exactly what was removed, what was installed, and the final position of every limit switch.

Before

After

What FAAC Gate Parts & Welding Costs in Miami Gardens

• Hinge replacement (single swing gate): $180-$320
• Hinge replacement (double swing gate): $340-$580
• Post replacement with welding: $420-$750, depending on post size and whether we have to dig out old concrete
• Rail repair or section replacement: $200-$450
• Custom welding (crack repair, brace gusset, decorative scrollwork): $150-$400 per weld point
• Gate roller replacement: $120-$250 per set
• Latch and lock re-alignment or replacement: $140-$280

The biggest variable is post condition. If a post is rotted at the base or cracked through, replacement is more involved than re-welding. The second variable is access: some Miami Gardens gates are built tight against a wall or fence line, which means we’re welding in a confined space. We’ll tell you the price before any work starts. Call (786) 789-0087 for a free estimate, and remember: the written price is the price.

Why Miami Gardens Homeowners Call Vance Gate Repair Miami Gardens for FAAC Work

We’re independent, which means we’ll tell you the truth about parts: if the OEM part is the right call, we’ll say so. If a quality aftermarket hinge kit does the same job for less, we’ll say that too. We don’t get a kickback either way. We’re also not exclusive to FAAC; we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing gates every week, so we’ve seen how different operators interact with different gate hardware. That matters when a FAAC operator was installed on a gate that originally ran a different brand. The way we work is the real reason people stay with us, though: written price in hand before a tool comes out, photos of every weld and hinge, and a 365-Day Done Right Promise that covers our work for a full year. In Miami Gardens, where the salt air works on everything metal, that promise means something.

FAQs